series am12tw-z 12 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12.c 1 of 4 north america only features: ? ultra wide input range 4:1 ? ? 1600 vdc isolation ? ? efficiency up to 90% ? ? soft start ? ? remote on/off function ? models single output model input voltage (v) output voltage (v) output current max (ma) isolation (vdc) maximum capacitive load (f) efficiency (%) am12tw-2403sz 9-36 3.3 3500 1600 2000 87 am12tw-2405sz 9-36 5.1 2400 1600 2000 89 am12tw-2412sz 9-36 12 1000 1600 430 90 am12tw-2415sz 9-36 15 800 1600 300 90 am12tw-4803sz 18-75 3.3 3500 1600 2000 87 am12tw-4805sz 18-75 5.1 2400 1600 2000 89 am12tw-4812sz 18-75 12 1000 1600 430 90 am12tw-4815sz 18-75 15 800 1600 300 90 models dual output model input voltage (v) output voltage (v) output current max (ma) isolation (vdc) maximum capacitive load (f) efficiency (%) am12tw-2405dz 9-36 5 1200 1600 1250 87 am12tw-2412dz 9-36 12 500 1600 200 90 am12tw-2415dz 9-36 15 400 1600 120 90 am12tw-4805dz 18-75 5 1200 1600 1250 87 am12tw-4812dz 18-75 12 500 1600 200 90 am12tw-4815dz 18-75 15 400 1600 120 90 input specifications parameters nominal typical maximum units voltage range 24 48 9-36 36-75 vdc filter ?
series am12tw-z 12 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12.c 2 of 4 north america only isolation specifications parameters conditions typical rated units tested i/o voltage 3 sec 1600 vdc tested case/input and output 1600 vdc resistance >1000 mohm capacitance 1500 pf output specifications parameters conditions typical maximum units voltage accuracy 1.2 % voltage balance dual output 5 % line voltage regulation hl-ll 0.2 % load voltage regulation (single) 0% load to full load 0.5 % load voltage regulation (dual) 0% load to full load 1.0 % over voltage protection zener diode clamp over current protection full load 170 % short circuit protection continuous short circuit restart auto recovery temperature coefficient 0.02 %/ o c ripple & noise 85 m vp-p general specifications parameters conditions typical maximum units switching frequency 100% load 270 khz operating temperature full load with derating above 60oc -40 to +85 o c storage temperature -40 to +125 o c max case temperature 105 o c derating above 60oc 2.5 % per 1oc cooling free air convection humidity 95 % rh case material nickel-coated copper weight 18.0 g dimensions (l x w x h) tolerance 0.5 mm or 0.02 inches 1.25 x 0.8 x 0.40 inches 31.75 x 20.32 x 10.16 mm mtbf >1 000 000 hrs (mil-hdbk -217f, ground benign, t=+25 o c) note: all specifications in this datasheet are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specified safety specifications parameters agency approval ce standards en55022 class a, en55024 iec61000-4-2, perf. criteria b iec61000-4-3, perf. criteria a iec61000-4-4, perf. criteria b (e xternal 330uf/100v cap required) iec61000-4-5, perf. criteria b (e xternal 330uf/100v cap required) iec61000-4-6, perf. criteria a iec61000-4-8, perf. criteria a note: also meets iec 60950-1:2001
series am12tw-z 12 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12.c 3 of 4 north america only pin out specifications dimensions bottom view 2.54 (0.10) 5.08 (0.20) printed face 0.50 (0.02) 31.80 (1.25) 23 9 11 14 16 22 23 1 all dimensions are typica l: millimeters (inches) pin diameter: 0.50 0.05 (0.02 0.002) pin pitch tolerance: 0.35 (0.014) case tolerence: 0.5 (0.02) 22.90 (0.90) derating pin single dual 1 remote on/off remote on/off 2 -v input -v input 3 -v input -v input 9 no pin common 11 n.c -v output 14 +v output +v output 16 -v output common 22 +v input +v input 23 +v input +v input
series am12tw-z 12 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12.c 4 of 4 north america only test circuits note: 1. datasheets are updated as needed and as such, specifications ar e subject to change without notic e. once printed or downloaded , datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency cert ifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specifications are measured at an am bient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary an d may not be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control sys tems or other such applications which necessitate specific safety and regulatory standards ot her the ones listed in this datasheet. 7. warranty is in accordance with aimtec?s st andard terms of sale available at www.aimtec.com.
|
